| GENERAL SPECIFICATIONS | |
| Weight - Standard Unit less accessories | 44,500 pounds (20,200kgs.) |
| Ground Bearing Pressure | 7.7 PSI (.54kgs./CM2) with 24 inch
(609.6MM) pads. 5.8 PSI (.41 kgs./CM2) with 30 inch (762MM) pads.
|
| Power Unit | Caterpillar turbocharged diesel Model 3304T. Horsepower 150 HP (112KW)......@2150 RPM |
| Wheel Transmission | Helical gear unit with high-torque capacity 4 digging wheel speeds plus one reverse speed 2-12 RPM forward. |
| Crawler Drive Vari-Crowd | Hydrostatic Drive-2 speed transmission with
Hi-Lo range for a total of four ranges forward or
reverse: 1-Lo, variable to 2.6 FPM (.8M/Min.) 1-Hi, variable to 29 FPM (8.7M/Min.) 2-Lo, variable to 14 FPM (4.3M/Min.) 2-Hi, variable to 156 FPM (42.5M/Min.) 1.8 MPH (2.9KM/HR) |
| Clutch | Main Clutch 14 inch (356MM) two plate clutch. Single lever controls all operations. Digging Clutch 10 inch (254MM) three plate, adjustable to load requirements. |
| Crawlers | Crawler Track 24 inch (610MM) wide rolled section grousers bolt to reinforced drop-forged rails, joined with bushed 1 1/2 inch (38.1MM) induction hardened pins. Sprockets...wide spaced alloy steel teeth drive on both ends of pins. 11 lower track rollers. 1000-hour lube service. Anti-friction bearings, sprockets and idles. Crawler Differential Hypoid unit Alloy steel heat treated shafts |
| Hydraulic Brakes | Hydraulic caliper type diusc with 18 inch (457MM) diameter rotor. |
| Main Frame | All welded, high-grade steel box type girder frame. |
| Boom | Single reinforced high tensile steel weldment. |
| Trucks | Upper Trucks 4 inch (101.6MM) dia. alloy steel shafts-H.T. Adjustable for variable cutting widths. Split wheels for ease of replacement. Anti-Friction bearing mounted. Lower Trucks Steel weldment body. Anti-friction bearing mounted wheels. Metal face seals. Bolt-on wheel rims, easily replaced. Front and rear Stay Rods Straight tubular compression mounted. |
| HYDRAULIC EQUIPMENT | |
| Hydraulic Boom Hoist Transmission | 2 high-torque, hydraulic motors for raising and lowering front and rear independently. |
| Hydraulic Pumps | Conveyor drive from piston pump for variable
belt speed. Separate dual pumps for independent control of hydraulic boom hoist and conveyor elevation. Crawler drive pump-variable displacement over center axial piston pump. |
| Hydraulic Reservior | Capacity - 60 gallons (227L.) Equipped with high-capacity return line filter, charge pump suction filter, cartridge type. Sealed hydraulic system. |
| Oil Cooler | High-capacity, air-to-oil hydraulic oil cooler |
| DIGGING WHEEL | |
| Engine Transmission | First gear...................2 Wheel RPM Second gear...............4 Wheel RPM Third gear...................7 Wheel RPM Fourth gear................12 Wheel RPM Reverse gear.............. ----------
|
| Digging Differential | Hypoid gearing. Heat treated alloy steel shafts. |
| Digging Wheel Rims | One piece, high tensile 1 inch (25.4MM) steel
plate. Match drilled in pairs Drop-forged heat treated alloy steel segments welded to rims. |
| Buckets | 15 flush, contour mounted 1 inch (25.4MM)
tensile steel. Drop forged ROTO-Tooth shanks, easy tap-on, knock-off. |
| Conveyor Drive | Patented planetary gear drives with external
gydraulic motors at each end. No chains or sprockets. Discharge Speed: 215-1000 FPM (64-305M/Min.) Speed and direction independently controlled. |
| Digging Wheel Drive Shaft | One piece-4 inch (101.6MM) diameter. Heat treated alloy steel on sealed bearings. Drop-forged hubs keyed to shaft accommodate, heat treated drop forged alloy steel split drive sprockets. |
| OPTIONAL EQUIPMENT | Carbide Teeth Bucket Fingers Center Cutters Bucket Cleaner Rock Guard Hydraulic Track Adjusters: 27 inch & 30 inch (686MM & 762MM) Track Shoes 1-1/8 inch (28.6MM) Rims 1-1/8 inch (28.6MM) Buckets 18 Buckets Slopers For difficult or unusual digging conditions, alternate tooth patterns available. Please Consult With Factory For Additional Options.
|
| NOTE: In accordance with varying material situations, and the Company's policy of constant product improvement, these specifications are subject to change without notice and without incurring responsibility to units previously sold. |